#Re web aluminum lawn chair with clips how to#
#Re web aluminum lawn chair with clips free#

Next, brush or spray on a metal primer, then apply an exterior enamel topcoat. Use a tiny touch-up brush on nicks, and a spray can on bigger scratches.įor wrought iron on tubular steel, use a wire brush and sandpaper to sand any rust spots or chipped paint down to bare metal.

There’s no need to prime-just apply exterior-grade acrylic enamel paint. For aluminum, rough up the surface slightly with 100-grit sandpaper, then smooth it with 220-grit paper. The method to use depends on the type of metal to be painted. The time to touch up nicks and scratches on the frame is after the old straps or slings have been removed and before the new ones go on. You’re done reviving your vinyl strap chair. Slide the loop up over the peg with your thumb, then let go of the strap.

#Re web aluminum lawn chair with clips free#

Keep tension on the strap as you push a peg through the free end and into its hole. Matthew Septimus Step 12: Secure the strap Hold it tight against this side with one hand use the other to loosely wrap the strap’s free end around the frame 1½ times. Grab the strap near its middle and stretch it to the opposite side of the frame. (For a single wrap, simply go halfway around the frame and pull to the opposite side.) Step 11: Stretch the strap to the other side With the peg seated firmly, wrap the strap all the way around the frame, covering the peg.

Matthew Septimus Step 10: Wrap the strap around the frame Attach the strap end by pushing a peg through its hole and into the hole on the back of the frame. Make the straps flexible by soaking them in hot (not boiling) water never use a hair dryer or heat gun. This is the best time to retouch or repaint your frame. (Metal clips can be reused.) The supplier will cut each strap to length and punch a hole for pegs or attach edge clips on both ends. Start at one hole, loop the tape measures fully around the frame, then pull to the opposite hole and repeat.īuy enough straps and pegs to redo the entire piece. A double-wrap strap (shown) covers the fasteners.

Matthew Septimus Step 8: Order new straps (for vinyl replacement)įor a single-wrap strap (one with exposed plastic pegs or metal clips), measure across the frame from hole to hole with a cloth tape measure wrapping around the outside of the frame. With a wire cutter, trim each rod flush with the end of the rail. Use a pipe clamp to spread the rails slightly if need be, bend the bar a bit to make it fit, then hit it with a rubber mallet to restore its shape. Matthew Septimus Step 6: Reattach the spreader bar Tighten the loose bolts on the opposite rail to make the sling taut. Slide the detached rail over the sling’s other nylon rod. Hold the sling with its hem side to the back and slide its nylon rod into the track of the rail that’s still attached to the chair frame. Matthew Septimus Step 4: Slide the new sling on Go to Frame Touch-Up Techniques for how-to and tips. Loosen but don’t remove the bolts that attach the rails to the chair frame, then pop out the spreader bar. Slide the two halves of the sling out of their tracks in the chair’s rails. (A damaged sling cannot be saved.) Remove the end cap on each side rail. Slash the old sling down the middle with a utility knife. Matthew Septimus Step 2: Cut the old sling To find the length, lay a cloth tape measure along the top face of one rail so it follows the rail’s curvature. To find the width, measure from the center of one rail to the center of the opposite rail at the bolt locations typically found at the top and bottom of the sling.

#Re web aluminum lawn chair with clips how to#

Related How to Care for Wood Patio Furniture Steps for Repairing Aluminum Patio Chairs Step 1: Order a new sling (for mesh sling replacement)īefore you get started on your patio sling chair repair, you have to measure your chairs and order replacement sling.